According to the differences in raw materials and preparation methods, conductive polymer composites can be divided into structural conductive composites, surface-treated conductive composites, and composite conductive composites. Structural conductive composites are inherently rigid, difficult to melt, hard to form, difficult to form, doped with most of the toxicity, poor electrical conductivity, high cost, and limited utility; surface-treated conductive composites have only one layer of conductive material on the surface. Abrasion, and the coated metal is easy to oxidize, the conductive effect can not be long; composite conductive polymer composite material refers to a composite material with a polymer material as a matrix, to which a variety of conductive materials are added, dispersed by lamination, various composites, etc. After the method is processed, a plurality of composite systems with a conductive function, which not only has a conductive function, but also has many excellent properties of polymer composite materials, can adjust electrical and mechanical properties in accordance with the needs of a wide range, and the cost is low. Therefore, the composite conductive polymer composite material should be widely thrown 1.3 performance test volume resistivity measurement such as plate-like sample and electrode configuration diagram, a sample inserted between the two electrodes to make a good connection angle applied to two The ratio of the DC voltage across the electrodes to the current flowing through the sample volume between them is called volume resistance Rv by Rv and The resistance coefficient calculated from the electrode and sample size is called the volume resistivity P r volume resistance, n mechanical properties measured tensile test methods see the bending strength test according to GB 1449-83 test. 2 Results and discussion (1) Performance test results and analysis Table 1 Copper powder as filler electrical content (parts by mass) Service sample thickness (mm) Resistance (n) Volume resistivity n.cm Note: Samples in this table The copper powder used was washed by acid pickling and vacuum drying. Table 2 Copper Powder as Filler Electrical Properties Content (parts by mass) Service Sample Thickness (mm) Resistance (n) Volume Resistivity ncm Note: The samples used in this table are used Copper powder was not treated. According to Table 1, Table 2 can be used to show the relationship between the volume resistivity and the filler content in the test Conductivity test results Discussion: The conductive mechanism of the polymer composite conductive material is relatively complex and can generally be divided into how the conductive loop is formed and how the loop is formed. In the two aspects of electrical conductivity, the former mainly studies the relationship between conductive fillers and the electrical properties of composite systems. Filler content-a tensile strength curve The filler content is determined by bending. Filler content-bending strength relationship diagram mechanical test results discussion: From the above main mechanical experimental results analysis shows that, with the gradual increase of Cu filler content, the overall tensile strength and bending strength curve of the product is gradually decreasing when the content is At 4% (%), the tensile strength and bending strength of the product did not decrease much as compared with the blank sample, which fully satisfied the engineering requirements. In this experiment, due to the addition of defoamer B, the porosity within the product was increased and the strength of the bond between the components was reduced. Therefore, as the filler content gradually increases to about 40%, the product maintains high strength. In the second test, the mechanical operation was adopted, the fillers were mixed evenly, and the products were molded steadily, which was also one of the important reasons for the stable mechanical properties of the products. 3 Conclusion The use of anti-oxidant A defoamer B, given metal filler conductive polymer products with excellent conductive properties Conductive polymer materials with treated copper powder as a conductive filler, when the mass of the filler is about 40%, the composite The best conductivity of the material In this test, when the mass fraction of copper powder is around 4 (%), the tensile strength and flexural strength of the product maintain a high level. Sodium Carboxymethyl Cellulose is a carboxymethylated derivative of cellulose, also known as cellulose gum, which is the main ionic cellulose gum. First made in 1918 and patented in 1921, it has since been commercialized in Europe. It was only for crude products and used as a gel and binder. In 1936 and 1941, the study of industrial applications was quite active and published several instructive patents. During world war ii, Germany will be used to synthesize detergent. Industrial production began in Germany in the 1930s with IG Farbenindustrie AG. Since then, the production process, production efficiency and product quality gradually improved. In 1947, the FDA confirmed that it was not toxic to the body, allowing it to be used as an additive in the food processing industry. Because of its many special properties, such as thickening, bonding, film forming, water holding, emulsification, suspension, etc., are widely used. In recent years, different qualities have been used in different fields of industry and people's lives. Sodium Carboxymethyl Cellulose Carboxymethylcellulose Sodium,Carboxymethyl Cellulose Sodium,Carboxymethyl Cellulose Sodium Cmc,Carboxymethyl Cellulose Sodium Nacmc Hebei pancan trading co. LTD , https://www.hbpancanshangmao.com
